 |
 |
|
DryFire System |
|
|
||
Dual-head DryFire Home Pack The Dual-head DryFire Home Pack contains everything you will need to get started. It includes the Dual-head DryFire Unit, the AC to DC Converter which supplies DC power to the Main Unit, a USB cable to connect the Unit to your computer, one (1) Combo Gun Assembly to properly equip your gun, the current version of the DryFire Software on a CD, and all the documentation required to load the software, set-up the system, and begin shooting. |
|
|||
Dual Head ATA Trapshooters Squad Pack The Squad Pack makes it easy to order everything you need to equip an entire five-man squad. The list includes:
|
|
|||
Single-head DryFire Home Pack The Single-head DryFire Home Pack contains everything you will need to get started. It includes the Single-head DryFire Unit, the AC to DC Converter which supplies DC power to the Main Unit, a USB cable to connect the Unit to your computer, one (1) Combo Gun Assembly to properly equip your gun, the current version of the DryFire Software on a CD, and all the documentation required to load the software, set-up the system, and begin shooting. |
|
|||
Single Head ATA Trapshooters Squad Pack The Squad Pack makes it easy to order everything you need to equip an entire five-man squad. The list includes:
|
|
|||
DryFire USA is now shipping this new, innovative dual trigger system standard with every Version 3 system. The Acoustic version works with YOUR TRIGGER and a Snap-Cap, while the Switch version mounts a micro-switch on the front surface of your trigger and you apply pressure to the switch until it activates and fires the gun (no Snap-Cap is used). Both versions use the Barrel Anchor which rigidly locks into the muzzle of your gun. The Laser Holder Assembly is then fastened to the protruding shaft of the Barrel Anchor with a set-screw. |
||||
 Click to enlarge |
Trigger Switch Gun Assembly The Trigger Switch version consists of a Switch Electronics module packaged in a small Red Box and a micro-switch molded into a rubber strap. The Red Box is attached to the receiver of your gun with the magnet bonded to it (locate it near your trigger). The two (2) pin connector attached to the micro-switch is plugged into the Red Box (you can't plug it in wrong). The round connector, on the far end of the Muzzle Laser cable, is plugged into the Red Box (Switch Electronics module). |
|
||
 Click to enlarge |
Acoustic Trigger Gun Assembly The Acoustic Trigger version consists of an Acoustic Pick-Up module packaged in the same small Red Box (it has a different label) and a Muzzle Laser, which is attached to the BArrel Anchor. The Acoustic Pick-Up is attached to the receiver of your gun with the magnet bonded to it. The round connector, on the far end of the Muzzle Laser cable, is plugged into the Red Box (Acoustic Pick-Up module). A small Blue Jumper must be lugged into the Red Box to connect the batteries to the circuitry and thereby turns it ON. |
|
||
 Click to enlarge |
Combo (Acoustic & Trigger Switch) Combination of the Acoustic version and the Trigger Switch version. |
|
||
 Click to enlarge |
DryFire Software CD DryFire's policy is to provide all customers with "Free" software updates. Therefore, the latest version is always available for download from our Downloads section. If, for whatever reason, you want the latest software on a CD we will be glad to ship it to you, but we will need to charge you a small amount to cover our cost. |
$5.00  |
||
Background Painting and Trap House DryFire USA highly recommends you add life to your shooting room by choosing one of our canvas wall hangings. About 50% of our customers purchase and use a canvas background. Almost every Trapshooter that buys a canvas also buys a 3D Styrofoam traphouse for use on the shooting wall (it is scaled to look just the right size indoors) and really adds a dimension of realism to your practice sessions. The canvas itself is light in weight, and yet very durable. The background scene is printed on the canvas with a state of the art linear printer capable of printing on 54 inch continuous roll stock. Our customers have come up with many ways of mounting the canvas on a wall. Some have stretched it over a wooden frame and then mounted the frame to the wall. Others have made a frame and then hung the frame from the ceiling. Another method is to use wallpaper paste to glue the canvas directly to the wall. If you use your imagination, we are sure you will find a way that best fits your needs. The canvas material is 54 inches vertically. But we sell the backgrounds in three (3) different widths and each has a different application. Canvas width: The distance you stand from the shooting wall determines the canvas width. The farther back you stand the wider the canvas must be. |
10 foot: Our ten (10) foot canvas works well in a small room where you intend to stand 8, 9, or 10 feet from the shooting wall. |
$225.00 |
|||
 Click to enlarge |
14 foot: Our fourteen (14) foot canvas works well with our Training Software, which requires a fourteen by fourteen foot room. We recommend you stand 10, 11, or 12 feet from the wall. At these distances, all the targets will remain on the canvas and the separation between shooters will be 26, 28, or 30 inches respectively. |
$275.00 |
||
 Click to enlarge |
18 foot: Our Skeet canvas is eighteen (18) feet wide and provides a good visual background for the USA Skeet layouts. We do not print a Skeet house on the left and right edge of the canvas. If you want Skeet houses on your canvas, we suggest you do what one of our customers did. He used a 1-inch thick piece of Styrofoam (15 inches wide and 28 inches tall) to make Skeet House silhouettes, then painted them, and attached them to the canvas with double face tape. We suggest you use your imagination and embellish your shooting wall to make it as real as you would like it to be. |
$350.00 |
||
 Click to enlarge |
The 3D Styrofoam Traphouse We provide three (3) different size traphouses. Each is scaled to be the correct size when simulating different yardages. The yardages are: 16 yard, 22 yard, and 27 yard. Therefore, when you mount your gun in relation to the DryFire 3D Traphouse the visual distances you see at the muzzle of your gun accurately simulate what you see at your local gun club.
|
16 Yard: $40.00
22 Yard: $35.00 27 Yard: $30.00 |
||
 Click to enlarge |
Hand Release Cord There are times, especially when operating the DryFire system in a noisy room, when the Voice Release system releases unwanted targets because of “the background sounds.” Therefore, we have included a Hand Release Cord in the standard “Squad Packs” because we know the Squad environment (especially in a clubhouse) can become quite noisy. The cord is 20 feet long and plugs directly into the back of your DryFire unit. The moment the cord is plugged in, the Voice Release circuit “goes to sleep” and later you can return to Voice Release by simply pulling the plug.
|
$40.00 |
||
 Click to enlarge |
Extra Barrel Anchor Replacement barrel anchor. The 12 gauge version is shown in the picture. An extra set of over-sized "O" rings are shipped with the 12 gauge Barrel Anchor to accommodate the "Big Bores" (barrels which have been bored out to 0.800"). The 20 and 28 gauge do not need over-sized "O" rings. |
|
||
 Click to enlarge |
Extra Laser Holder with Laser The Gun Laser is not repairable. Therefore, if it fails after it is out of warranty, you may want to purchase a replacement. |
$65.00 |
||
 Click to enlarge |
Extra Red Trigger Box (Switch) The Red Trigger Box is not repairable. Therefore, if it fails after it is out of warranty, you may want to purchase a replacement. |
$65.00 | ||
 Click to enlarge |
Extra Red Trigger Box (Acoustic) The Red Trigger Box is not repairable. Therefore, if it fails after it is out of warranty, you may want to purchase a replacement. |
$50.00 | ||
 Click to enlarge |
Extra Trigger Switch The Trigger Switch is not repairable. Therefore, if it fails after it is out of warranty, you may want to purchase a replacement. |
$30.00 |
||
 Click to enlarge |
Extra Snap Cap Replacement Snap Cap. |
|||
 Click to enlarge |
Extra Batteries (set of three) The batteries are not under warranty, if you can't purchase them locally, we will supply them as a set of three (3). The price listed is for one (1) set of three (3). |
$3.00 |
||
 Click to enlarge |
Training Software (developed by DryFire USA)
for "ATA Trapshooting ONLY"
In 2007 DryFire USA wrote a version of software to allow multiple Trapshooters to shoot together in a squad. Recently, DryFire USA re-wrote the 2007 multi-user Squadding software and because of the changes made, has changed the name to "Training Software." Besides shooting in squads, as the Squadding Software allowed, the new Training Software allows individuals or squads to customize their target patterns (allowing each individual to practice his or her weaknesses). And also has introduced a very powerful feature called, "Remote Coaching." Remote Coaching allows a coach to e-mail training sessions to a student, who loads and shoots the training sessions, and then e-mails the training session results back to the coach for analysis. This means it is now possible to be coached by someone who does not live near you. |
$495.00 |
||
